User can choose the most suitable equipments for their own test requirements to build automotive test platform. It breaks through the traditional testing system limitation,providing professional testing steps toimprove testing efficiency. ITS5300 Battery charge-discharge testing system is comprised of power supply, electronic load,internal resistance tester, temperature data acquisition instrument and IT9320 software. Likewise, if the power-off state continues for long, the system will automatically cut off the active charge/discharge circuit so as to prevent overcharge and over-discharge and guarantee the safety and reliability of battery testing. In this way, repeated tests are avoided for higher efficiency. With the protection function, previously acquired data can be effectively stored intact in case of unexpected power failure or computer crash during a time-consuming aging test and the user may proceed with the test program from the faulty link after the system is back to normal. Power-off memory feature is the most cutting-edge and perfect protection function developed by ITECH and designed for time-consuming aging tests. ITS5300 Test System is superior over traditional integrated charge & discharge device in that it has a power-off memory feature while the latter has single protection configuration only. If the reading is above 12 volts, then the battery. The reading on the load tester will tell you if the battery is healthy or not. Once the load tester is connected, turn on the tester and wait for the reading. Then, connect the load tester to the battery. That is not only easy for observation and record, but also improves the testing To use a 12 volt battery load tester, first make sure that the battery is fully charged. The software has intuitive colored block charts to symbolize normality or abnormality of cell characteristics and give early warning where necessary, including channel configuration, cell voltage, current, discharge capacity and other parameters. During the test, user can clearly observe the test information of each channel through the software. Apart from key parameters of each channel, ITS5300 test system may install a thermograph and IR tester to realize real-time monitoring of cell voltage, IR and temperature. For this reason, monitoring of cells is of great importance. Real-time Charging & Discharging Monitor of Each ChannelĪ battery pack is typically a set of cells connected in series which exhibit different characteristics during charge and discharge. Furthermore, the software will help the user monitor cell voltage, temperature and IR, produce charge/discharge curves and monitor and store relevant data. By editing test steps, the user may perform constant current charge, constant pressure charge and constant current/power/resistance discharge tests on multi-channel cells or battery packs. ITS5300 Test System is equipped with a battery charge/discharge testing software developed on the basis of user specifications. ♦ Adopt GPIB communication, support multi-system extension. ![]() ♦ A complete alarm and protection setup for effectively preventing overcharge, over-discharge and other unexpected faults. Measured temperature depends on the type of thermocouple user selected. Support cell battery AC internal resistance analysis and battery packĭC internal resistance analysis. ♦ Real-time online monitoring on single module resistance, voltage and temperature. ♦ Standard modular design not only makes it easy for hardware extension and follow-up maintenance but also expand its applications. ♦ High reliability and high precision guarantee absolute measurement accuracy within the broad voltage/current range, making the test system more efficient in use. ♦ Fast response and high-speed sampling rate, sampling rate and data storage time down to 1ms. * Discharge mode: CC / CR / CP / pulse discharge Tests NiMH, Alkaline, and Lithium.♦ Balance charging and discharging capacity, designed for battery module / cell test. Negative test lead/probe conveniently stores in seam at side. Its small size makes it ideal for the gadget bag, toolbox, or home utility drawer. Item: Pulse Load Battery Tester For Use With: Residential or Commercial Detectors Power Source: (4) AA Batteries Width: 8 in Height: 12 in. There are no settings, and test results are easy to understand. Battery types are clearly labeled next to appropriate contacts. ![]() After a fully automatic test cycle, percentage of remaining battery capacity is indicated on the LED bar display. ![]() The MINI-MBT's microprocessor-based design makes battery testing simple - using a patented, high accuracy pulse load test. Pulse Load Mini Multi-Battery Tester MINI-MBT provides a comprehensive means of testing the state of charge or state of power for more than 15 battery types. Pulse Load Mini Multi-Battery Tester MINI-MBT for Alkaline, Lithium, NiMH
0 Comments
Leave a Reply. |